Skip to main content
Download PDF
Download ePub

Adsorptive removal of heavy metals from wastewater using Cobalt-diphenylamine (Co-DPA) complex

BMC Chemistry volume 18, Article number: 23 (2024) Cite this article

Abstract

Heavy metals like Cadmium, Lead, and Chromium are the pollutants emitted into the environment through industrial development. In this work, a new diphenylamine coordinated cobalt complex (Co-DPA) has been synthesized and tested for its efficiency in removing heavy metals from wastewater, and its adsorption capacity was investigated. The effectiveness of heavy metals removal by Co-DPA was evaluated by adjusting the adsorption parameters, such as adsorbent dose, pH, initial metals concentration, and adsorption period. Heavy metal concentrations in real sample were 0.267, 0.075, and 0.125 mg/L for Cd2+, Pb2+, and Cr3+ before using as-synthesized Co-DPA to treat wastewater. After being treated with synthesized Co-DPA the concentration of heavy metals was reduced to 0.0129, 0.00028, 0.00054 mg/L for Cd2+, Pb2+, and Cr3+, respectively, in 80 min. The removal efficiency was 95.6%, 99.5%, and 99.5% for the respective metals. The adsorption process fitted satisfactorily with Freundlich isotherm with R2(0.999, 0.997, 0.995) for Cd2+, Pb2+, and Cr3+, respectively. The kinetic data obeyed the pseudo-second order for Cd2+ and Cr2+ and the pseudo-first order for Pb2+. Based on the results obtained within the framework of this study, it is concluded that the as-synthesized Co-DPA is a good adsorbent to eliminate heavy metal ions like Cd2+, Pb2+, and Cr3+from wastewater solution. In general, Co-DPA is a promising new material for the removal of heavy metal ions from water.

Graphical Abstract

Peer Review reports

Introduction

Heavy metal ions are one of the major sources of water contamination [1]. Exposure to heavy metal ions consequences in a huge threat to both human health and ecological balance due to their carcinogenic nature [1,2,3]. Wastewater originated from industries such as paint manufacture, mining activities, metal plating, electroplating industry, batteries, pesticides, and fluidized bed bioreactors, etc., are known to have high concentrations of various heavy metal ions, such as copper (Cu), arsenic (As), cadmium (Cd), mercury (Hg), and lead (Pb) [1,2,3]. This heavy metal-polluted wastewater is discharged into the natural water resources, threatening human health and the ecosystem [2,3,4,5]. The heavy metals are carcinogenic and non-biodegradable, which get piled up in living organisms, further generating several critical health issues and syndromes such as fleeting growth and development, impairment of the nervous system, obstructive lung disease, and death in extreme cases [5,6,7]. Lead and cadmium both have nephrotoxic effects and are linked to bone deterioration and encephalopathy at high exposure levels [8,9,10,11,12]. Hence, industrial wastewater must be treated before releasing into the rivers or ponds to exclude these toxic heavy metals. The World Health Organization has set guidelines for the acceptable levels of lead and cadmium in wastewater, which are 0.015 mg/L and 0.01 mg/L, respectively [8, 11, 12]. Hexavalent chromium is poisonous and carcinogenic at high enough quantities resulting in Ulcers and perforation of nasal septum, and respiratory cancer [7].

Various conventional methods have been investigated for the removal of heavy metal ions like precipitation, ion exchange, advanced oxidation processes, membrane filtration, electrocoagulation (EC), reverse osmosis, etc. [13,14,15,16,17,18,19,20]. However, most of these techniques have substantial operating costs and require the disposal of the solid waste they produce. The adsorption method is a superior technique due to its lesser operating cost, straightforward implementation, high removal efficiency, easy regeneration of the adsorbent, and production of little or no byproduct [21,22,23,24,25]. The mechanism of the adsorption process is based on the physicochemical properties of heavy metals and adsorbent and operating conditions (i.e., pH value, adsorbent amount, temperature, adsorption time, and initial concentration of metal ions) [26,27,28]. Usually, heavy metal ions can be adsorbed on the surface of the adsorbent via intermolecular interactions. The amputation of heavy metals from numerous sources of wastewater has reportedly been accomplished using commercial activated carbon [15, 29, 30], zeolites, and biomass-derived adsorbents like peanut shells [31,32,33], banana peel [34, 35], dry tree leaves [36], rice husk [37], tea and coffee waste [38], coconut shell powder [39], papaya seed [40], and eggshell [41]. Nevertheless, some problems, including the need for a prolonged reaction time, excessive calcination temperature, inadequate stability, short reusability, a low surface area, etc. restrict most of the available adsorbents [15, 16, 29, 31, 42]. As a result, it is crucial to create low-cost adsorbents with a large surface area utilizing straightforward synthesis techniques. The characteristics of a promising ion adsorbent are high adsorption kinetics, substantial adsorption capacities even at low contamination levels, selectivity for the target ion, stability in the aqueous environment, scalability, recoverability, and cost [25, 27, 30, 34, 36, 43,44,45,46,47,48]. Physical adsorption and chemical adsorption are the two main categories of adsorption processes [15]. Weak bonds (van der Waals force and dipolar forces) and low heats of adsorption are characteristics of physisorption [15]. The attraction between permanent dipoles and induced dipoles also allows adsorbate molecules to freely cover the whole surface of the adsorbent without changing the species' atomic or molecular orbitals. As a result, adsorbate molecules are not constrained to locations. However, chemisorption comprises the interchange of electrons between the adsorbate and the adsorbent [42]. For the elimination of Co (II) ions from aqueous solutions, activated carbons made from hazelnut shell were utilized as adsorbents displayed adsorption capacity as 58.27 mg g−1 [49, 50]. Activated carbon from Borassus aethiopum seed shells (BASS) and Cocos nucifera (CONS) was studied by Mohammed and Azim for the removal of Pb2+ and Cd2+ (shells) showing 99% and 95% removal for Pb2+ and Cd2+ respectively [51]. In 2020 Wang and coworkers synthesized Ferrous phosphate to treat wastewater containing EDTA-Pb from 50 mg Pb/L to < 1 mg Pb/L [52]. In 2021 Asma et al. reported sodium alginate grafted by diphenylamine as adsorbent for the removal of Co2+ ions through adsorption process where the adsorption capacity was dependent on the pH value [53]. The maximum removal capacity was credited to the electrostatic attraction between the metal ions and the negative charge of adsorbent surface. In 2020 Ngoc T. et al. reported hydrogen-bonded supramolecular complex for efficient removal of trace heavy metal ions from water exhibiting adsorption kinetics, up to 50 times faster than state-of-the-art materials for selective copper ion capture from water [54]. In 2018, Xu et al. reported selective adsorption of Cu (II) and SO42− ions through silica gel-immobilized Schiff base derivative [55]. In 2020 Jumina et al. reported the removal of Pb2+, Cr2+, and Cu2+ metal ions through pH Dependent adsorption process using C-Phenylcalix pyrogallolarene [4]. The phenolic group of the adsorbent increases the metal uptake efficiency through the ion exchange process [56]. Some recent examples of adsorbents are summarized below showing operation conditions and removal efficiency (Table 1) as comparison with our study.

Table 1 A comparative table to include operation conditions, and removal efficiency
Full size table

This study aims to investigate the removal of heavy metals from wastewater using cobalt-complex (Co-DPA) under different experimental conditions. The Co-DPA was prepared from the cobalt nitrate hexahydrate (Co (NO3)2.6H2O), and diphenylamine, in solution of water and ethanol (1:1v/v ratio). The Co-DPA was characterized by XRD, and FTIR. A wastewater sample was collected from Gurage zone Butajira town around textile fabric from Akamuj river, Ethiopia. Heavy metals removal capacity of Co-DPA was determined, and batch experiments were conducted to look at the effects of pH, dose, initial metal concentration, and contact time on the adsorptions of heavy metals. The effect of condition parameters like concentration of lead, chromium, cadmium, and contact time was studied to obtain the optimum condition with high removal efficiency. The measurement of the concentration of heavy metals before and after treatment with the prepared Co-DPA was done by AAS.

Materials and methods

Materials

All chemicals and reagents procured were of analytical grade and used without additional purification. Cobalt (II) nitrate hexahydrate, ethanol, diphenylamine, hydrochloric acid, sodium hydroxide, Nitric acid, Perchloric acid, Lead (II) chloride, Cadmium (II) chloride, and Chromium (III) chloride were purchased from Sigma Aldrich. Following a minimum 24-h soak in 10% Nitric acid, all vessels were cleaned by being repeatedly washed with deionized (DI) water. Real samples of heavy metal ions (Cd2+, Pb2+, and Cr3+) with metal concentrations as 0.267, 0.075, and 0.125 mg/L respectively were collected from Gurage zone Butajira town around textile fabric from Akamuj river, Ethiopia. The standard solution of Cd, Pb, and Cr were prepared by dissolving metal precursors in distilled water.

Synthesis of cobalt-complex

Cobalt complex (Co-DPA) was synthesized via facile approach using cobalt (II) nitrate hexahydrate (Co (NO3)2.6 H2O). 24.69 g of cobalt nitrate hexahydrate was dissolved in 5 mL of distilled water, and 5 g of diphenylamine was dissolved in 5 mL of ethanol. The two solutions were combined and swirled on a hot plate magnetic stirrer for an hour to create a homogenous solution. The mixture was then preserved for 3 days, and a reddish-pink precipitate was formed. The formed precipitate was filtered by filter paper using suction filtration and dried in a drying oven at 40 °C for 24 h. The attained precipitate, named Co-DPA subsequently, was retained for further characterization and experiments.

Characterization

Powder X-ray diffraction (PXRD) technique was used to study the purity and crystallinity of the bulk material (Shimadzu XRD- 7000). FT-IR (Fourier-transform infrared) spectroscopy was used to examine the surface functional groups of the Co-DPA complex (PerkinElmer spectrometer). A DW-AA320N Atomic Absorption spectrometer (AAS) was used for metal adsorption studies.

Collection of waste-water sample

Wastewater was collected from Gurage zone, Butajira town, Ethiopia from the car wash labajo area and transported to Chemistry laboratory, Hawassa University, Ethiopia. The sample was fixed by adding 3 drops of 69% nitric acid and stored at 4 ℃ for heavy metals determination before and after the treatment. The actual concentrations of heavy metals were measured by using AAS, before being treated by Co-DPA.

Batch adsorption experiment to optimize adsorption parameters

Batch adsorption tests were performed to observe the effect of pH, initial metal ions concentration, adsorbent dosage, adsorption kinetics, adsorption isotherms, and period of mixing needed to attain equilibrium for Pb(II), Cr(III), and Cd(II) adsorbed by Co-DPA.

pH study

To determine the effect of pH on the removal of heavy metals from wastewater, the metals sample working solution was prepared. 20 mg/L metals concentration and 3 g/L of Co-DPA were added to the pH optimized as 3, 5, 7, 9 and 11, then centrifuged for 30 min and the supernatant was used to measure heavy metals concentration.

Results and discussion

Characterization of Co-DPA

Powder X-ray diffraction (XRD) analysis was considered to examine the structure and crystallinity of the samples (Fig. 1). The intensity of the detected rays about scattering angle two theta (2θ) was used to ascertain the crystalline nature of the as-synthesized Co-DPA. The crystallite domain size (grain size) was calculated from the width of the peaks using Scherrer’s formula. As shown in Fig. 1, the calculated grain size, from average of the tallest peak, at an angle of 2θ is 34.55 nm. The calculated grain size (mean diameter of the particle) is greater than 2 nm and less than 50 nm, which is the characteristic nature of mesoporous materials from Scherrer’s equation [67].

Fig. 1
figure 1

PXRD graph of synthesized Co-DPA

Full size image

The FTIR spectra were acquired using a Perkin Elmer FT-IR spectrometer in transmission mode. With a resolution of 4 cm−1 (Fig. 2), each sample in the KBr mix was scanned 64 times from 4,000 to 400 cm−1. The secondary N–H vibration at frequencies (3380 and 3040 cm−1) after complex formation showing coordination of the amine nitrogen atom. The peaks appeared around 1582, 1493, and 1453 cm−1 is assigned for the C=C stretching vibrations for the aromatic rings of the diphenylene ligand coordinated to the metal center. The strong searching vibration peak appeared around 742 and 688 cm−1 are confirmed the coordination of Co-with N of the diphenylene ligand.

Fig. 2
figure 2

FT-IR graph of synthesized Co-DPA

Full size image

Optimization of adsorption parameters

Adsorption behaviour was analyzed by a batch method, where factors that affect the process of adsorption such as pH, adsorbent dose, initial metals concentration, and contact time were investigated. The standard solution of Pb, Cd, and Cr were prepared by dissolving metal precursors in distilled water.

Effect of pH

For adsorbent Co-DPA the effect of pH on the removal efficiency of heavy metals was considered from a range of 3 to 11 under the precise conditions (at a contact time of 30 min, 20 mg/L adsorbate solution with 3 g of the adsorbent and temperature of 25 °C with an agitation speed of 150 rpm). The percentage of Pb(II) and Cd(II) adsorbed by Co-DPA first increases with an increase in pH from pH 3–7 and then decreases later (Fig. 3a). For Cr(III) ion, the maximum removal efficiency obtained is at pH 3. The maximum percent removal of heavy metal ions was obtained at pH 7 for Cd and Pb and at pH 3 for Cr, which is 92.4%, 94.05%, and 92.5%, respectively (Fig. 3b). For Lead high removal efficiency obtained at pH 7 is the same as the results obtained by Li et al. on the removal of chromium from wastewater by Mg-Loaded Biochars with the removal efficiency of 87% partaking the maximum adsorption capacity of 2.7 mg/g [68]. The high removal efficiency of cadmium obtained at pH 7 is the same as the result obtained by Bayuo et al. [69] on the removal of heavy metals from wastewater using shea fruit shell biomass. Most of the adsorption space for the elimination of cadmium and lead could be occupied by protons, at lower pH levels (pH 3.0). The proton attached is released from active sites at moderate pH, and the quantity of adsorbed metal rises. The metal precipitate can occur at high pH levels (pH > 7), which reduces adsorption. Cation exchange and surface complexation are two potential explanations for why metal’s adsorption capacities increase when pH rises. The delayed adsorption at high pH is results from slow diffusion into the adsorbent's bulk and an electrostatic barrier between positively charged adsorbate species that have been adsorbed onto the surface of the adsorbent and cationic adsorbate species that are present in the solution [70]. Moreover, the unique nature of chromium and the adsorbent surface explains the high adsorption capacity of metallic chromium on an adsorbent surface at lower pH. At high pH value Cr(III) adsorption onto Co-DPA decreases as metal ions react with OH¯ ions and gets precipitated as a metal hydroxide. As a result, this pH was chosen as the ideal value for the remaining studies [71,72,73].

Fig. 3
figure 3

Graphical representation of the impact of initial pH on a adsorption capacity and b removal efficiency (with error bar) of Cd2+, Pb2+, and Cr3+ by Co-DPA (error bars represent ± standard experimental errors)

Full size image

Effect of adsorbent dosage

The impact of the adsorbent dose was analyzed by the variable quantity of Co-DPA from 1 to 4 g and kept other parameters constant (pH 3 for Cr and pH 7 for Cd and Pb, 20 mg/L adsorbate concentration, 30 min contact time). As shown in Fig. 4a, the adsorption capacity was found to be highest at the lowest adsorbent concentration and reduced as the dose rose. In this work, As the adsorbent dose increased, the adsorption capacity declined, which was attributed to adsorption sites staying unsaturated throughout the adsorption reaction due to the increased number of accessible adsorption sites favoring enhanced metal ion uptake. Adsorption dosage increased due to the availability of a greater surface area and adsorption sites for a constant amount of metal ions, and accessible sites would overlap [73, 74].

Fig. 4
figure 4

Graphical illustration of the impact of adsorbent dosage on a adsorption capacity  b removal efficiency (with error bar) of Cd2+, Pb2+ and Cr3+ by Co-DPA (error bars represent ± standard experimental errors)

Full size image

When the adsorbent dose was increased from 1 to 4 g, the percentage of Cr (III), Cd (II), Pb(II) removal was increased (Fig. 4). As the dosage amount increased from 1 to 3, the removal efficiency rose from 71.9% to 90.05% for Pb2+, from 91.4 to 94% for Cd2+, and 92.55 to 94 0.05% for Cr3+. The superior removal efficiency was obtained when the adsorbent dosage was 3 g i.e., 90.05%, 94%, and 94.05%, respectively. No change was observed when dosage amount increased to 4 g (Fig. 4b). The higher number of accessible adsorption sites encouraged the enhanced uptake of the metal ions which is the cause of the constant adsorption capacity with increasing doses of adsorbent [48, 74].

Effect of initial metals concentration

Metal ions standard solutions in the following concentrations: 20, 40, 60, and 80 mg/L were generated, and the other parameters kept similar as before. Co-DPA was used to treat the solutions, and an AAS was used for analysis. The % removal varied consistently as the starting concentration of heavy metal ions changed. For Cr (III), Pb(II), and Cd(II), the percent removal for metal ions falls as the initial concentration slowly rises to 60 mg/L, then declines rapidly as the initial concentration rises to 80 mg/L. The adsorption capacity increased as the concentration of metals increased (Fig. 5a). It is evident from the Figure that the percentage of Pb2+, Cd2+, and Cr3+ removal efficiency decreased from 89.35% to 74.9475% for Cd2+, 82.75% to 77.5% for Pb2+, 90.55% to 84.375% for Cr3+ with the increase in initial concentration of metal ions (Fig. 5b). Different heavy metal ions may have different chemical affinities and ion exchange capacities concerning the chemical functional group on the surface of the adsorbent, which can explain differences in the percentage of different heavy metal ions eliminated at the same initial metal ions concentration, dose, and contact duration [30, 47, 48, 74, 75].

Fig. 5
figure 5

Representation of the impact of initial metals concentration on a adsorption capacity and b removal efficiency of Cd2+, Pb2+ and Cr3+ by Co-DPA with error bars (error bars represent ± standard experimental errors)

Full size image

Effect of contact time

The effects of contact time Pb(II), Cd(II), andCr (III) adsorption on Co-DPA at different adsorption times (20, 40, 60, 80, 100, and 120 min) is shown in (Fig. 6), and pH 3 for Cr (III) and 7 for Cd(II) and Pb(II), adsorbent dose 3 g, initial concentration was 60 mg/L. The initial adsorption was highly rapid, and as the adsorption duration increased, the sorption kinetics increased gradually until the adsorption eventually hit equilibrium in 80 min in the case of Cd2+ and Cr3+ with a removal efficiency of 92.85 and 93.785%, respectively (Fig. 6). Pb2+ had a high removal efficiency of 90.13% at 60 min, matching the findings of Kowsura et al. [76]. Cadmium (II) adsorption by Co-DPA has maximum removal efficiency of 92.85% which is the same as the result obtained by [74] with a maximum adsorption capacity of 33 mg/g at 80 min. During the adsorption process at the initial stage, many vacant sites are available for adsorption. As adsorption time progresses the active sites are occupied by adsorbates which make constant adsorption efficiency. This may be clarified by the fact that originally, the ion absorption rate was higher since entire sites on the adsorbent were unoccupied and the concentration of ions was high, but that rate remained constant as all sites were filled consequently because doing so prevents the additional adsorbate from being taken up [30, 34, 48].

Fig. 6
figure 6

Graphical representation of the impact of contact time on a adsorption capacity and b removal efficiency of Cd2+, Pb2+ and Cr3+ by Co-DPA with error bars (error bars represent ± standard experimental errors)

Full size image

Adsorption experiment for real sample

The collected wastewater sample was brought to the laboratory for the adsorption experiment and digested with 4 mL nitric acid and 2 mL perchloric acid for 80 min at a temperature of 120 °C. 20 mL of digested sample was taken, and 3 g of the synthesized Co-DPA was added and allowed to shake on a reciprocating shaker for 80 min to determine Pb, and 3 g of the synthesized Co-DPA was added and allowed to shake on a reciprocating shaker for 80 min to determine Cd2+ and Cr3+. The sample was filtered by filter paper and brought to measure heavy metals concentration by AAS. The removal efficiency and adsorption capacity were estimated. The metal ions concentration before being treated with synthesized Co-DPA recorded for Cd2+, Pb2+, and Cr3+ was 0.267 mg/L, 0.075 mg/L, and 0.125 mg/L, respectively. After being treated with the adsorbent the concentration of the metal was obtained as 0.0129, 0.00028, and 0.00054 for Cd2+, Pb2+, and Cr3+, respectively. For Cd2+, Pb2+, and Cr3+, the removal efficiencies of the adsorbent for heavy metals in actual samples were determined to be 95.6%, 99.5%, and 99.5% respectively.

Recovery studies

Reusing the adsorbent by regenerating its adsorption characteristics is an economic necessity in many applications. With growing raw material and wastewater treatment process expenses, the allure of product recovery technologies has grown dramatically [74, 77]. The Cu-DPA adsorbent was evaluated for its reusability. The recycling results shown in Fig. 7 show that it maintains its activity despite a decline in metal ion removal efficiency, and it is pH dependent and performed by adding HCl and NaOH to solution.

Fig. 7
figure 7

Illustration of the percent removal of heavy metal ions from real wastewater sample along with the reusability studies for Co-DPA complex

Full size image

In a typical experiment, 0.01 M HNO3 or HCl and 0.005 M NaOH eluents were added to the solution to perform the recycling test. Metals were initially adsorbed on Cu-DPA from 60 mL solutions containing 80 mg/L metal ions at pH 3 (Cr) and 7 (Cd &Pb). The Cu-DPA were then stripped with 30 mL eluent while agitating at 25 °C for 30 min. The Cu-DPA complex was separated, and the metal ion concentration in the supernatant was determined. The adsorption–desorption cycles were done three times for each measurement.

Adsorption isotherms

Figure 8 demonstrates the adsorption isotherm with fitting models. Adsorption isotherms are often used to explain equilibrium studies that provide the adsorbent's capacity and the equilibrium interactions between adsorbent and adsorbate [30, 36, 44, 78,79,80]. Adsorption isotherms are the fraction of the quantity adsorbed and remaining in solution at set temperature as equilibrium. The Langmuir and Freundlich isotherms are the original and most basic proven relations that illustrate the adsorption equation. The fundamental tenet of the Langmuir hypothesis is that once a metal molecule occupies a particular homogenous location inside the adsorbent, no further adsorption can take place there. A description of the Langmuir isotherm model is stated in Eq. (1).

$$\frac{{\varvec{C}}{\varvec{e}}}{{\varvec{q}}{\varvec{e}}}=\frac{1}{{{\varvec{K}}}_{{\varvec{L}}}{\varvec{q}}{\varvec{m}}}+\boldsymbol{ }\frac{{\varvec{C}}{\varvec{e}}}{{\varvec{q}}{\varvec{m}}}.$$
(1)

where qm symbolizes the maximum monolayer adsorption capacity (mg/g), KL stands for Langmuir constant associated with the energy of adsorption (L/g), Ce and qe are the equilibrium concentration (mg/L), and adsorption capacity (mg/g) respectively. The equation above produces a straight line with a slope of 1/qm and an intercept of 1/KLqm when plotting Ce/qe vs Ce (Fig. 8).

Fig. 8
figure 8

Langmuir adsorption isotherm for a Cd2+, b Pb2+, and c Cr3+

Full size image

There are interactions between molecules that have been adsorbed and heterogeneous surface energy systems in multilayer adsorption, which is expressed by the Freundlich isotherm model. Equation (2) used to describe the Freundlich isotherm. In this case, the Freundlich isotherm model's constants for sorption capacity (KF) and sorption intensity (1/n) are involved, and the exponent (1/n) indicates the system's favorability and capacity. Comparing log qe to log Ce from the previous equation yields a straight line with a slope of 1/n and an intercept of log KF (Fig. 9). The slope 1/n, which has a value between 0 and 1, is a measure of surface heterogeneity or adsorption intensity, which turn additionally heterogeneous because its value attempts to zero. Normal Langmuir isotherm is designated by a value of 1/n below one, and cooperative adsorption is implied by a value of 1/n above one [81]. The KF is an assessment of adsorption capacity increased with concentration for Pb2+, Cd2+, and Cr3+ adsorption. The magnitude of the exponent n shows the favorability and capacity of the adsorbent/adsorbate system. 1/n for Cd2+, Pb2+, and Cr3+ is 0.79005, 0.880, and 0.74007, respectively. These values are the measure of favorability of the adsorption of adsorbate on the heterogeneous surface of the adsorbent [32, 69, 71]. Karthikeyan et al. have stated that the favorable adsorption condition is represented through n values between 1 and 10.

Fig. 9
figure 9

Freundlich adsorption isotherm for a Cd2+, b Pb2+ and c Cr3+

Full size image
$${\varvec{log}}\,{\varvec{qe}}={\varvec{log}}{{\varvec{K}}}_{{\varvec{F}}}+\frac{1}{{\varvec{n}}}{\varvec{log}}{\varvec{C}}{\varvec{e}}$$
(2)

To determine the favorable or unfavorable behavior of an adsorption system, Hall et al. [82] introduced a dimensionless separation factor or equilibrium parameter, RL, as a crucial component of the Langmuir isotherm, which is specified as in Eq. (3).

$$RL = 1/1+KLCo$$
(3)

where co represents the adsorbate’s initial concentration (mg/L), KL defines Langmuir constant (L/mg). If RL > 1.0, the sorption isotherm remains unfavorable; = 1.0 (linear); 0 < RL < 1.0 (favorable) and RL = 0 (irreversible) [83]. The achieved findings (RL = 0.357, 0.436, 0.271 for Cd2+, Pb2+ and Cr3+, respectively) confirms that the sorption of Cd2+, Pb2+ and Cr3+ onto the Co-DPA was favorable.

Table 2 lists the isotherm parameters for the Pb(II), Cd(II), and Cr(III) adsorption in the Langmuir and Freundlich models. The values of R2 of the Langmuir model were lower than Freundlich isotherm model R2 (Cd2+(0.995), Pb2+(0.997), Cr3+(0.996)), from which it was concluded that the adsorption of Pb(II), Cd(II) and Cr(III) ions fitted better in the Freundlich isotherm model. This showed that the adsorption of Cr(III), Pb(II), and Cd(II) was directed by multilayer adsorption on a heterogeneous surface of an adsorbent. The n value greater than 1 (n > 1) is documented as an L-type isotherm indicating significant affinity among adsorbate and adsorbent and revealing chemisorption. The Freundlich adsorption capacity (KF) reveals the removal of heavy metal ions from wastewater facilely. The greater the adsorption intensity the higher the KF value.

Table 2 Analyzed isotherm parameters for the adsorption of Cd2+, Pd2+ and Cr3+ on to Co-DPA
Full size table

The fraction of the Co-DPA surface covered by Cd2+, Pd2+, and Cr3+ was calculated from the optimized concentration using Eq. (4).

$$\uptheta =1 -\frac{Ce}{ Co}$$
(4)

where θ is a fraction of surface coverage, Co is the initial metal ions concentration and Ce is the equilibrium metal ions concentration. The calculated fraction of surface coverage during the adsorption of Cd2+, Pd2+, and Cr3+ onto Co-DPA is presented in Table 3. The fraction of Co-DPA surface covered by Cd2+, Pd2+, and Cr3+ was obtained as 0.8935, 0.8275, and 0.835 for Cd2+, Pd2+, and Cr3+ respectively. These values indicate that 89.35%, 82.75%, and 83.5% of the pore space of Co-DPA is covered by metal ions which is the same as the result obtained on the removal of lead from wastewater by Co-DPA.

Table 3 The fraction of the Co-DPA surface covered by Cd2+, Pd2+, and Cr3+
Full size table

The number of hopping (n) an adsorbate makes, as determined by Eq. (5), may be associated with the probability that it will discover an empty site on the adsorbent surface during sorption (5).

$${\text{n}}=\frac{1}{(1-\theta )\theta }.$$
(5)

where n is the number of hopping done by the adsorbate and θ is the surface coverage. By using Eq. (5) the number of hopping done by adsorbate to find vacant sites on Co-DPA was obtained as 10.504, 6.993, and 7.246 for Cd2+, Pd2+, and Cr3+, respectively.

Adsorption kinetics

The kinetics of cadmium, lead, and chromium adsorption onto Co-DPA were investigated using the pseudo-second order and pseudo-first order kinetic models to suggest which model the sorption system follows. This can be described by models of pseudo-first order and pseudo-second order. Scientifically pseudo first order is stated as in Eq. (6):

$${\varvec{log}}\,\left({\varvec{qe}}-{\varvec{qt}}\right)={\varvec{log}}\,{\varvec{qe}}-\frac{{\varvec{K}}1}{2.303}\mathbf{t}$$
(6)

where qt expresses the adsorption capacity at time t, qe symbolizes the equilibrium adsorption capacity (mg/g), and K1 means the pseudo-first-order rate constant (g/mg) which can be estimated by plotting between log (qe-qt) and t (Fig. 10).

Fig. 10
figure 10

Pseudo-first orders kinetic model of a Cd2+, b Pb2+, and (c) Cr3+

Full size image

Pseudo-second order kinetic model is stated mathematically as in Eq. (7):

$$\frac{t}{{q_{t} }} = \frac{1}{{K_{2} qe^{2} }} + \frac{1}{{q_{e} }}{\text{t}}$$
(7)

where K2 expresses the rate constant for pseudo-second order (g mg−1 min−1). The value of qe was estimated through the plot between t/qt and t (Fig. 11).

Fig. 11
figure 11

Pseudo-second order kinetic model of a Cd2+, b Pb2+, and c Cr3+

Full size image

From the pseudo-first and second order kinetic model linear plotted with different adsorption time and kinetic model constants like k1, k2, and qe values were determined from the slope and intercept of plots, are represented in Table 3. Table 3 reveals that the linear plot of Cd2+ and Cr3+ shown in Figs. 10 and 11 has a higher R2 value in the pseudo-second order. This shows that the kinetics data suit perfectly with the pseudo-second-order model. The computed values of qe almost matched with the experimental data obtained from the pseudo-second-order kinetics in addition to the larger values of R2 (Table 4). Also, it was noted that the values of k1 were higher than the comparable values of k2. The best fit for the Pb2+ adsorption studies were therefore believed to be the pseudo first-order kinetic model. The kinetics results from various investigations were also said to fit the pseudo-second-order kinetic model quite well; including the adsorption of Cd2+ ions on Jatropha peel, adsorption of Pb2+ ions on pumpkin seed shell activated carbon, adsorption of Pb2+ ions on Co-DPA, and adsorption of Cr3+ ions on cooked tea dust [43].

Table 4 Calculated kinetic parameters for the adsorption of Cd2+, Pb2+,  and Cr3+ on to Co-DPA
Full size table

Conclusion

The Co-DPA complex was easily produced from cobalt (II) nitrate hexahydrate and diphenylamine linker. Co-DPA was evaluated for its efficacy in removing heavy metal ions from wastewater and its adsorption capacity. From this study, it is concluded that the Co-DPA is an excellent adsorbent for the removal of the heavy metal ions such as Cd2+, Pb2+, and Cr3+ from wastewater samples. The effect of adsorption factors such as contact time, pH value, initial metals concentration, and adsorbent (synthesized Co-DPA) dose on adsorption capacity and removal efficiency was examined. The removal efficiency was recorded as 95.6%, 99.5%, and 99.5% for the Cd2+, Pb2+, and Cr3+, respectively. More importantly, the adsorption isotherm was governed by Freundlich isotherm and adsorption mechanism was pseudo-first order for Pb2+ and pseudo-second order for Cd2+, and Cr3+. This suggests that a multilayer has formed on the surface of the adsorbent. Therefore, the synthesized Co-DPA complex could be a potential candidate for the massively efficient adsorptive removal of heavy metal ions from wastewater.

Data availability

The datasets used and/or analyzed in this study are accessible in the publication and can be obtained upon request from the corresponding author.

References

  1. Gorchev HG, Ozolins G. WHO guidelines for drinking-water quality. WHO Chron. 1984;38:104–8.

    CAS  PubMed  Google Scholar 

  2. Ahluwalia SS, Goyal D. Microbial and plant derived biomass for removal of heavy metals from wastewater. Biores Technol. 2007;98:2243–57.

    Article  CAS  Google Scholar 

  3. Ke F, Qiu L-G, Yuan Y-P, Peng F-M, Jiang X, Xie A-J, et al. Thiol-functionalization of metal-organic framework by a facile coordination-based postsynthetic strategy and enhanced removal of Hg2+ from water. J Hazard Mater. 2011;196:36–43.

    Article  CAS  PubMed  Google Scholar 

  4. Dhakshinamoorthy A, Alvaro M, Garcia H. Aerobic oxidation of styrenes catalyzed by an iron metal organic framework. ACS Catal. 2011;1:836–40.

    Article  CAS  Google Scholar 

  5. Kothapalli CR. Differential impact of heavy metals on neurotoxicity during development and in aging central nervous system. Curr Opin Toxicol. 2021;26:33–8.

    Article  CAS  Google Scholar 

  6. Mitra S, Chakraborty AJ, Tareq AM, Emran TB, Nainu F, Khusro A, et al. Impact of heavy metals on the environment and human health: novel therapeutic insights to counter the toxicity. J King Saud Univ Sci. 2022;34: 101865.

    Article  Google Scholar 

  7. Mohanty S, Benya A, Hota S, Kumar MS, Singh S. Eco-toxicity of hexavalent chromium and its adverse impact on environment and human health in Sukinda Valley of India: a review on pollution and prevention strategies. Environ Chem Ecotoxicol. 2023;5:46–54.

    Article  CAS  Google Scholar 

  8. Zhong G, Lu S, Chen R, Chen N, Tan Q-G. Predicting risks of cadmium toxicity in salinity-fluctuating estuarine waters using the Toxicokinetic-Toxicodynamic Model. Environ Sci Technol. 2020;54:13899–907.

    Article  CAS  PubMed  Google Scholar 

  9. Hui C, Guo Y, Li H, Gao C, Yi J. Detection of environmental pollutant cadmium in water using a visual bacterial biosensor. Sci Rep. 2022;12:6898.

    Article  CAS  PubMed  PubMed Central  Google Scholar 

  10. Kubier A, Wilkin RT, Pichler T. Cadmium in soils and groundwater: a review. Appl Geochem. 2019;108: 104388.

    Article  CAS  Google Scholar 

  11. Turner MC, Andersen ZJ, Baccarelli A, Diver WR, Gapstur SM, Pope CA, et al. Outdoor air pollution and cancer: an overview of the current evidence and public health recommendations. CA A Cancer J Clin. 2020;70:460–79.

    Article  Google Scholar 

  12. Rousseau M-C, Parent M-E, Nadon L, Latreille B, Siemiatycki J. Occupational exposure to lead compounds and risk of cancer among men: a population-based case-control study. Am J Epidemiol. 2007;166:1005–14.

    Article  PubMed  Google Scholar 

  13. Raouf Ms A, Raheim AR. Removal of heavy metals from industrial waste water by biomass-based materials: a review. J Pollut Eff Cont. 2016;5:1–13.

    Article  Google Scholar 

  14. Yari M, Norouzi M, Mahvi AH, Rajabi M, Yari A, Moradi O, et al. Removal of Pb(II) ion from aqueous solution by graphene oxide and functionalized graphene oxide-thiol: effect of cysteamine concentration on the bonding constant. Desalin Water Treat. 2016;57:11195–210.

    Article  CAS  Google Scholar 

  15. Bernal V, Giraldo L, Moreno-Piraján JC. Physicochemical parameters of the methylparaben adsorption from aqueous solution onto activated carbon and their relationship with the surface chemistry. ACS Omega. 2021;6:8797–807.

    Article  CAS  PubMed  PubMed Central  Google Scholar 

  16. Geng H, Xu Y, Zheng L, Gong H, Dai L, Dai X. An overview of removing heavy metals from sewage sludge: achievements and perspectives. Environ Pollut. 2020;266: 115375.

    Article  CAS  PubMed  Google Scholar 

  17. Gupta S, Benien P, Sahoo PK. Ion exchange resins transforming drug delivery systems. Curr Drug Deliv. 2010;7:252–62.

    Article  CAS  PubMed  Google Scholar 

  18. Prifti H, Parasuraman A, Winardi S, Lim TM, Skyllas-Kazacos M. Membranes for redox flow battery applications. Membranes. 2012;2:275–306.

    Article  CAS  PubMed  PubMed Central  Google Scholar 

  19. Lee H. Characterization of anion exchange membranes fouled with humate during electrodialysis. J Membr Sci. 2002;203:115–26.

    Article  CAS  Google Scholar 

  20. Garba MD, Usman M, Mazumder MAJ, Al-Ahmed A, Inamuddin. Complexing agents for metal removal using ultrafiltration membranes: a review. Environ Chem Lett. 2019;17:1195–208.

    Article  CAS  Google Scholar 

  21. Al-Ghouti MA, Da’ana D, Abu-Dieyeh M, Khraisheh M. Adsorptive removal of mercury from water by adsorbents derived from date pits. Sci Rep. 2019;9:15327.

    Article  PubMed  PubMed Central  Google Scholar 

  22. Mohammad A, Ansari SN, Chaudhary A, Ahmad K, Rajak R, Tauqeer M, et al. Enthralling adsorption of different dye and metal contaminants from aqueous systems by cobalt/cobalt oxide nanocomposites derived from single-source molecular precursors. ChemistrySelect. 2018;3:5733–41.

    Article  CAS  Google Scholar 

  23. Sarkar S, Adhikari S. Adsorption technique for removal of heavy metals from water and possible application in wastewater-fed aquaculture. In: Jana BB, Mandal RN, Jayasankar P, editors. Wastewater management through aquaculture. Singapore: Springer Singapore; 2018. p. 235–51.

    Chapter  Google Scholar 

  24. Syahirah Kamarudin N, Jusoh R, Dina Setiabudi H, Fateha Sukor N, Haslinda SJ. Potential nanomaterials application in wastewater treatment: physical, chemical, and biological approaches. Mater Today Proc. 2021;42:107–14.

    Article  CAS  Google Scholar 

  25. Mahmoudi MM, Nasseri S, Mahvi AH, Dargahi A, Khubestani MS, Salari M. Fluoride removal from aqueous solution by acid-treated clinoptilolite: isotherm and kinetic study. DWT. 2019;146:333–40.

    Article  CAS  Google Scholar 

  26. Priyadarshanee M, Das S. Biosorption and removal of toxic heavy metals by metal tolerating bacteria for bioremediation of metal contamination: a comprehensive review. J Environ Chem Eng. 2021;9: 104686.

    Article  CAS  Google Scholar 

  27. Jiang J-Q, Ashekuzzaman S. Development of novel inorganic adsorbent for water treatment. Curr Opin Chem Eng. 2012;1:191–9.

    Article  CAS  Google Scholar 

  28. Asiabi H, Yamini Y, Shamsayei M, Tahmasebi E. Highly selective and efficient removal, and extraction of heavy metals by layered double hydroxides intercalated with the diphenylamine-4-sulfonate: a comparative study. Chem Eng J. 2017;323:212–23.

    Article  CAS  Google Scholar 

  29. Jha MK, Joshi S, Sharma RK, Kim AA, Pant B, Park M, et al. Surface modified activated carbons: sustainable bio-based materials for environmental remediation. Nanomaterials. 2021;11:3140.

    Article  CAS  PubMed  PubMed Central  Google Scholar 

  30. Pourali P, Rashtbari Y, Behzad A, Ahmadfazeli A, Poureshgh Y, Dargahi A. Loading of zinc oxide nanoparticles from green synthesis on the low cost and eco-friendly activated carbon and its application for diazinon removal: isotherm, kinetics, and retrieval study. Appl Water Sci. 2023;13:101.

    Article  CAS  Google Scholar 

  31. Almasi A, Omidi M, Khodadadian M, Khamutian R, Gholivand MB. Lead(II) and cadmium(II) removal from aqueous solution using processed walnut shell: kinetic and equilibrium study. Toxicol Environ Chem. 2012;94:660–71.

    Article  CAS  Google Scholar 

  32. Gautam RK, Mudhoo A, Lofrano G, Chattopadhyaya MC. Biomass-derived biosorbents for metal ions sequestration: adsorbent modification and activation methods and adsorbent regeneration. J Environ Chem Eng. 2014;2:239–59.

    Article  CAS  Google Scholar 

  33. Mathabatha TIK, Matheri AN, Belaid M. Peanut shell-derived biochar as a low-cost adsorbent to extract cadmium, chromium, lead, copper, and zinc (heavy metals) from wastewater: circular economy approach. CircEconSust. 2023;3:1045–64.

    CAS  Google Scholar 

  34. Mohammadifard A, Allouss D, Vosoughi M, Dargahi A, Moharrami A. Synthesis of magnetic Fe3O4/activated carbon prepared from banana peel (BPAC@Fe3O4) and salvia seed (SSAC@Fe3O4) and applications in the adsorption of Basic Blue 41 textile dye from aqueous solutions. Appl Water Sci. 2022;12:88.

    Article  CAS  Google Scholar 

  35. Li Y, Liu J, Yuan Q, Tang H, Yu F, Lv X. A green adsorbent derived from banana peel for highly effective removal of heavy metal ions from water. RSC Adv. 2016;6:45041–8.

    Article  CAS  Google Scholar 

  36. Dargahi A, Samarghandi MR, Shabanloo A, Mahmoudi MM, Nasab HZ. Statistical modeling of phenolic compounds adsorption onto low-cost adsorbent prepared from aloe vera leaves wastes using CCD-RSM optimization: effect of parameters, isotherm, and kinetic studies. Biomass Conv Bioref. 2023;13:7859–73.

    Article  CAS  Google Scholar 

  37. Chuah TG, Jumasiah A, Azni I, Katayon S, Thomas Choong SY. Rice husk as a potentially low-cost biosorbent for heavy metal and dye removal: an overview. Desalination. 2005;175:305–16.

    Article  CAS  Google Scholar 

  38. Çelebi H, Gök G, Gök O. Adsorption capability of brewed tea waste in waters containing toxic lead(II), cadmium (II), nickel (II), and zinc(II) heavy metal ions. Sci Rep. 2020;10:17570.

    Article  PubMed  PubMed Central  Google Scholar 

  39. Pinheiro Do Nascimento PF, Lins De Barros Neto E, Fernandes De Sousa J, Trocolli Ribeiro V, De Jesus Nogueira Duarte L, Fonseca Melo RP, et al. Metal ion adsorption using coconut shell powder activated by chemical and physical treatments. Chem Eng & Technol. 2021;44:2199–209.

    Article  CAS  Google Scholar 

  40. Hameed BH. Evaluation of papaya seeds as a novel non-conventional low-cost adsorbent for removal of methylene blue. J Hazard Mater. 2009;162:939–44.

    Article  CAS  PubMed  Google Scholar 

  41. Zonato RDO, Estevam BR, Perez ID, Aparecida Dos Santos Ribeiro V, Boina RF. Eggshell as an adsorbent for removing dyes and metallic ions in aqueous solutions. Cleaner Chem Eng. 2022;2:100023.

    Article  Google Scholar 

  42. Huber F, Berwanger J, Polesya S, Mankovsky S, Ebert H, Giessibl FJ. Chemical bond formation showing a transition from physisorption to chemisorption. Science. 2019;366:235–8.

    Article  CAS  PubMed  Google Scholar 

  43. Obregón-Valencia D, Sun-Kou MDR. Comparative cadmium adsorption study on activated carbon prepared from aguaje (Mauritia flexuosa) and olive fruit stones (Olea europaea L.). J Environ Chem Eng. 2014;2:2280–8.

    Article  Google Scholar 

  44. Shokoohi R, Dargahi A, Azami Gilan R, Zolghadr Nasab H, Zeynalzadeh D, Molla MM. Magnetic multi-walled carbon nanotube as effective adsorbent for ciprofloxacin (CIP) removal from aqueous solutions: isotherm and kinetics studies. Int J Chem Reactor Eng. 2020;18:20190130.

    Article  CAS  Google Scholar 

  45. Jafari S, Zhao F, Zhao D, Lahtinen M, Bhatnagar A, Sillanpää M. A comparative study for the removal of methylene blue dye by N and S modified TiO2 adsorbents. J Mol Liq. 2015;207:90–8.

    Article  CAS  Google Scholar 

  46. Dargahi A, Rahimpouran S, Rad HM, Eghlimi E, Zandian H, Hosseinkhani A, et al. Investigation of the link between the type and concentrations of heavy metals and other elements in blood and urinary stones and their association to the environmental factors and dietary pattern. J Trace Elem Med Biol. 2023;80: 127270.

    Article  CAS  PubMed  Google Scholar 

  47. Farrokhi M, Naimi- Joubani M, Dargahi A, Poursadeghian M, Jamali HA. Investigating activated sludge microbialpopulation efficiency in heavy metals removalfrom compost leachate. Pol J Environ Stud. 2018;27:623–7.

    Article  CAS  Google Scholar 

  48. Dargahi A, Gholestanifar H, Darvishi P, Karami A, Hasan SH, Poormohammadi A, et al. An Investigation and comparison of removing heavy metals (lead and chromium) from aqueous solutions using magnesium oxide nanoparticles. Pol J Environ Stud. 2016;25:557–62.

    Article  CAS  Google Scholar 

  49. Anirudhan TS, Sreekumari SS. Adsorptive removal of heavy metal ions from industrial effluents using activated carbon derived from waste coconut buttons. J Environ Sci. 2011;23:1989–98.

    Article  CAS  Google Scholar 

  50. Filice S, Bongiorno C, Libertino S, Compagnini G, Gradon L, Iannazzo D, et al. Structural characterization and adsorption properties of dunino raw halloysite mineral for dye removal from water. Materials. 2021;14:3676.

    Article  CAS  PubMed  PubMed Central  Google Scholar 

  51. Abdulrazak S, Hussaini K, Sani HM. Evaluation of removal efficiency of heavy metals by low-cost activated carbon prepared from African palm fruit. Appl Water Sci. 2017;7:3151–5.

    Article  CAS  Google Scholar 

  52. Mohan B, Kamboj A, Virender, Singh K, Priyanka, Singh G, et al. Metal-organic frameworks (MOFs) materials for pesticides, heavy metals, and drugs removal: Environmental safety. Separat Purif Technol. 2023;310:123175.

    Article  CAS  Google Scholar 

  53. Ahmed A, Mohamed F, Elzanaty AM, Abdel-Gawad OF. Synthesis and characterization of diphenylamine grafted onto sodium alginate for metal removal. Int J Biol Macromol. 2021;167:766–76.

    Article  CAS  PubMed  Google Scholar 

  54. Bui NT, Kang H, Teat SJ, Su GM, Pao C-W, Liu Y-S, et al. A nature-inspired hydrogen-bonded supramolecular complex for selective copper ion removal from water. Nat Commun. 2020;11:3947.

    Article  CAS  PubMed  PubMed Central  Google Scholar 

  55. Xu Z, Wang K, Liu Q, Guo F, Xiong Z, Li Y, et al. A bifunctional adsorbent of silica gel-immobilized Schiff base derivative for simultaneous and selective adsorption of Cu(II) and SO42−. Sep Purif Technol. 2018;191:61–74.

    Article  CAS  Google Scholar 

  56. Jumina, Priastomo Y, Setiawan HR, Mutmainah, Kurniawan YS, Ohto K. Simultaneous removal of lead(II), chromium(III), and copper(II) heavy metal ions through an adsorption process using C-phenylcalix[4]pyrogallolarene material. J Environ Chem Eng. 2020;8: 103971.

    Article  CAS  Google Scholar 

  57. Zheng Y, Rao F, Zhang M, Li J, Huang W. Efficient, selective, and reusable metal–organic framework-based adsorbent for the removal of Pb(II) and Cr(VI) heavy-metal pollutants from wastewater. Clean Eng Technol. 2021;5: 100344.

    Article  Google Scholar 

  58. Rahaman MH, Md. slam A, Md. slam M, Md. Rahman A, Alam SMN. Biodegradable composite adsorbent of modified cellulose and chitosan to remove heavy metal ions from aqueous solution. Curr Res Green Sustain Chem. 2021;4: 100119.

    Article  CAS  Google Scholar 

  59. Mahmud M, Md. Mossain S, Bin Mobarak M, Sultana S, Sharmin S, Ahmed S. Co-precipitation synthesis of non-cytotoxic and magnetic cobalt ferrite nanoparticles for purging heavy metal from the aqueous medium: Pb(II) adsorption isotherms and kinetics study. Chem Ecol. 2022;38:544–63.

    Article  CAS  Google Scholar 

  60. Mohammadi SZ, Mofidinasab N, Karimi MA, Mosazadeh F. Fast and efficient removal of Pb(II) ion and malachite green dye from wastewater by using magnetic activated carbon–cobalt nanoparticles. Water Sci Technol. 2020;82:829–42.

    Article  CAS  PubMed  Google Scholar 

  61. Paris EC, Malafatti JOD, Musetti HC, Manzoli A, Zenatti A, Escote MT. Faujasite zeolite decorated with cobalt ferrite nanoparticles for improving removal and reuse in Pb2+ ions adsorption. Chin J Chem Eng. 2020;28:1884–90.

    Article  CAS  Google Scholar 

  62. El Mouden A, El Messaoudi N, El Guerraf A, Bouich A, Mehmeti V, Lacherai A, et al. Multifunctional cobalt oxide nanocomposites for efficient removal of heavy metals from aqueous solutions. Chemosphere. 2023;317: 137922.

    Article  PubMed  Google Scholar 

  63. Anuma S, Mishra P, Bhat BR. Polypyrrole functionalized Cobalt oxide Graphene (COPYGO) nanocomposite for the efficient removal of dyes and heavy metal pollutants from aqueous effluents. J Hazard Mater. 2021;416: 125929.

    Article  CAS  PubMed  Google Scholar 

  64. Jayalakshmi R, Jeyanthi J, Aswin Sidhaarth KR. Versatile application of cobalt ferrite nanoparticles for the removal of heavy metals and dyes from aqueous solution. Environ Nanotechnol Monit Manag. 2022;17: 100659.

    CAS  Google Scholar 

  65. Alves Macedo JC, Sartori Jeunon Gontijo E, Gómez Herrera S, Rangel EC, Komatsu D, Landers R, et al. Organosulphur-modified biochar: an effective green adsorbent for removing metal species in aquatic systems. Surf Interfaces. 2021;22: 100822.

    Article  CAS  Google Scholar 

  66. Srivastava V, Kohout T, Sillanpää M. Potential of cobalt ferrite nanoparticles (CoFe2O4) for remediation of hexavalent chromium from synthetic and printing press wastewater. J Environ Chem Eng. 2016;4:2922–32.

    Article  CAS  Google Scholar 

  67. Holzwarth U, Gibson N. The Scherrer equation versus the “Debye-Scherrer equation.” Nat Nanotech. 2011;6:534–534.

    Article  CAS  Google Scholar 

  68. Li A, Deng H, Jiang Y, Ye C. High-efficiency removal of Cr(VI) from wastewater by Mg-loaded biochars: adsorption process and removal mechanism. Materials. 2020;13:947.

    Article  CAS  PubMed  PubMed Central  Google Scholar 

  69. Bayuo J. Decontamination of cadmium(II) from synthetic wastewater onto shea fruit shell biomass. Appl Water Sci. 2021;11:84.

    Article  CAS  Google Scholar 

  70. Wang C, Boithias L, Ning Z, Han Y, Sauvage S, Sánchez-Pérez J-M, et al. Comparison of Langmuir and Freundlich adsorption equations within the SWAT-K model for assessing potassium environmental losses at basin scale. Agric Water Manag. 2017;180:205–11.

    Article  Google Scholar 

  71. Ghoneim MM, El-Desoky HS, El-Moselhy KM, Amer A, Abou El-Naga EH, Mohamedein LI, et al. Removal of cadmium from aqueous solution using marine green algae, Ulva lactuca. Egypt J Aquat Res. 2014;40:235–42.

    Article  Google Scholar 

  72. Farooq U, Kozinski JA, Khan MA, Athar M. Biosorption of heavy metal ions using wheat based biosorbents – a review of the recent literature. Biores Technol. 2010;101:5043–53.

    Article  CAS  Google Scholar 

  73. Giraldo L, Moreno-Piraján JC. Pb2+ adsorption from aqueous solutions on activated carbons obtained from lignocellulosic residues. Braz J Chem Eng. 2008;25:143–51.

    Article  CAS  Google Scholar 

  74. Haso HW, Dubale AA, Chimdesa MA, Atlabachew M. High performance copper based metal organic framework for removal of heavy metals from wastewater. Front Mater. 2022;9: 840806.

    Article  Google Scholar 

  75. Meena AK, Kadirvelu K, Mishraa GK, Rajagopal C, Nagar PN. Adsorption of Pb(II) and Cd(II) metal ions from aqueous solutions by mustard husk. J Hazard Mater. 2008;150:619–25.

    Article  CAS  PubMed  Google Scholar 

  76. Department of Environmental Engineering, Faculty of Engineering, Khon Kaen University, Kowsura C, Pangkumhang B, Jutaporn P, Tanboonchuy V. Isotherm models of heavy metal sorption onto zinc-tricarboxylic. IJCEA. 2017;8:179–83.

    Article  Google Scholar 

  77. Gupta NK, Kim S, Bae J, Kim KS. Chemisorption of hydrogen sulfide over copper-based metal–organic frameworks: methanol and UV-assisted regeneration. RSC Adv. 2021;11:4890–900.

    Article  CAS  PubMed  PubMed Central  Google Scholar 

  78. Almasi A. Efficiency of a constructed wetland in controlling organic pollutants, nitrogen, and heavy metals from sewage. J Chem Pharm Sci. 2016;9:2924–8.

    CAS  Google Scholar 

  79. Alavi N, Shamshiri S, Pariz Z, Dargahi A. Evaluating the palm leaves efficiency as a natural adsorbent for removing cadmium from aqueous solutions: isotherm adsorption study. J Pharm Technol. 2016;8:13919–29.

    CAS  Google Scholar 

  80. Gnanasekaran G, Arthanareeswaran G, Mok YS. A high-flux metal-organic framework membrane (PSF/MIL-100 (Fe)) for the removal of microplastics adsorbing dye contaminants from textile wastewater. Separat Purif Technol. 2021;277: 119655.

    Article  CAS  Google Scholar 

  81. Liu S. Cooperative adsorption on solid surfaces. J Colloid Interface Sci. 2015;450:224–38.

    Article  CAS  PubMed  Google Scholar 

  82. Murphy OP, Vashishtha M, Palanisamy P, Kumar KV. A review on the adsorption isotherms and design calculations for the optimization of adsorbent mass and contact time. ACS Omega. 2023;8:17407–30.

    Article  CAS  PubMed  PubMed Central  Google Scholar 

  83. Tseng R-L, Wu F-C. Inferring the favorable adsorption level and the concurrent multi-stage process with the Freundlich constant. J Hazard Mater. 2008;155:277–87.

    Article  CAS  PubMed  Google Scholar 

Download references

Acknowledgements

Mesfin Yimer, Binyam Abdu, and Wubshet Mekonnen Girma is grateful to the Department of Chemistry, College of Natural Science, Wollo University, Ethiopia, for granting access to their research facilities.

Funding

Wollo University funded this research through a graduate student support program.

Author information

Authors and Affiliations

  1. Department of Chemistry, College of Natural Science, Wollo University, P.O. Box:1145, Dessie, Ethiopia

    Mesfin Yimer, Biniyam Abdu Berehe & Wubshet Mekonnen Girma

  2. Department of Chemistry, School of Engineering, Presidency University, Bangalore, Karnataka, 560064, India

    Shagufi Naz Ansari

  3. Department of Chemistry, School of Science, GITAM (Deemed to Be University), Rudraram, Telangana, 502329, India

    Krishna Kanthi Gudimella

  4. Central Research Laboratory, K S Hegde Medical Academy, NITTE (Deemed to Be University), Deralakatte, Mangaluru, Karnataka, 575018, India

    Gangaraju Gedda

  5. Department of Animal Science & Technology and BET Research Institute, Chung-Ang University, Anseong, Gyeonggi-do, 17546, Republic of Korea

    Gangaraju Gedda

  6. Department of Chemistry, College of Science, Jazan University, P.O. Box 114, Jazan, 45142, Kingdom of Saudi Arabia

    Nazim Hasan & Shadma Tasneem

Authors
  1. Mesfin Yimer
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Shagufi Naz Ansari
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Biniyam Abdu Berehe
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Krishna Kanthi Gudimella
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Gangaraju Gedda
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Wubshet Mekonnen Girma
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. Nazim Hasan
    View author publications

    You can also search for this author in PubMed Google Scholar

  8. Shadma Tasneem
    View author publications

    You can also search for this author in PubMed Google Scholar

Contributions

MY, SNA, and BAB performed the synthesis of Co-DPA, characterization, and performance analysis of results writing-draft and conceptualization of work, KKG and, GG performed an analysis of results, manuscript correction, and scientific discussion, WMG performed an analysis of results, manuscript correction, scientific discussion, supervision, and review-editing, and NA and ST performed editing, and correction. All authors reviewed the manuscript.

Corresponding authors

Correspondence to Gangaraju Gedda or Wubshet Mekonnen Girma.

Ethics declarations

Ethics approval and consent to participate

Not applicable.

Consent for publication

Not applicable.

Competing interests

The authors declare that there is no conflict of interest.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated in a credit line to the data.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Yimer, M., Ansari, S.N., Berehe, B.A. et al. Adsorptive removal of heavy metals from wastewater using Cobalt-diphenylamine (Co-DPA) complex. BMC Chemistry 18, 23 (2024). https://doi.org/10.1186/s13065-024-01128-z

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1186/s13065-024-01128-z

Keywords

BMC Chemistry

ISSN: 2661-801X

Contact us